Categories: Electronics Moudles
A2212 1000 KV BLDC Brushless DC Motor for Drone (Soldered Connector)
- Motor KV: 1000
- Current Capacity: 12A/ 60S
- LiPO Batteries: 2S-3S
- Max. Efficiency Current: 4-10A
- Shaft Diameter: 3.17 mm
0 Reviews Write a review
Categories: General
AI-BO8 ADVANCE KIT
Ultra Sonic Sensor 1
Joystick 1
PIR Sensor 1
Buzzer (S) 1
Single Seven Segment Display 1
Gas Sensor 1
DHT 11 1
Touch Sensor 1
ESP32 1
HC05 1
GSM 1
IRFZ44N Mosfet 1
LDR Module 1
Sound Detection Module 1
SD Card Module 1
Light Sensor 1
GPS Module 1
Soind Module 1
Color Sensor 1
Rain Drop Sensor 1
RTC Module 1
IR Sensor 1
Soil Moisture Sensor 1
Buzzer (B) 1
Car Set 1
2 Channel Relay 1
4*4 Keypad 1
DC Pump 1
Ultra Sonic Sensor Stand 1
12V Battery 1
Jumpers Wire (M-M) 40
Jumpers Wire (M-F) 40
Jumpers Wire (F-F) 40
9V Battery Connector 1
Small Breadboard 1
Big Breadboard 1
RFID Tag 1
Motor Driver Sheild 1
Solar Panel 1
Magnet 1
IR remote 1
0 Reviews Write a review
Categories: 3D Printer & Accessories
AiBo8 3D Printer
I3 style printer
Linear rod and linear bearing bearing mechanism
Touch Screen 32 bit motherBoard
Made in india robust power supply and all aluminum design
0 Reviews Write a review
Categories: Electronics Moudles
All Purpose Hot Melt Glue Sticks for Glue Gun – 5pcs
- Diameter: 11mm
- Length: 190mm
0 Reviews Write a review
Arduino Nano
The Nano Board R3 with CH340 chip without USB Cable chipboard is based on the famous Arduino platform and does all the functions of Uno, but with a smaller footprint. The Nano Board R3 with CH340 chip without USB Cable is vital for your small project where you don’t need much of pin-outs but the small size is very important to make it look good.
0 Reviews Write a review
Arduino Nano Shield
The Nano 328P Expansion Adapter Breakout Board IO Shield acts as a breakout board for the Arduino Nano microcontroller. There are several different options for power input and the footprint of this board is the same as the Arduino Duemilanove.
0 Reviews Write a review
Arduino Uno
The Arduino Uno R3 with Cable is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs); 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button.
It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.
0 Reviews Write a review
Categories: General
Basic Electronics Kit
In this kit, you will get a variety of electronic components that can be used to construct or enhance your knowledge of many types of electronic components. Out of the box, the kit has products Resisters, Battery holders, Breadboard, Battery connectors, Jumper wires.
0 Reviews Write a review
Battery clips with DC Jack
This 9V battery holder allows your battery to snap in tight and holds it in place, which is great in situations where you don’t want the battery just hanging. It also has three mounting holes so you can attach it securely to your enclosure. It is terminated with a standard 5.5 x 2.1 mm, centre-positive barrel jack.
The holders are moulded in Delrin with corrosive resistant nickel plated springs and studs. A PP3 battery holder moulded in black thermoplastic with DC JACK can be screwed to a base for the most secure mounting.
0 Reviews Write a review